കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് 2023, ഡൗൺലോഡ് PDF

കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ്

കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ്: കേരള പബ്ലിക് സർവീസ് കമ്മീഷൻ ഔദ്യോഗിക വെബ്സൈറ്റായ @www.keralapsc.gov.in ൽ കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് പ്രസിദ്ധീകരിച്ചു. പരീക്ഷയ്ക്കുള്ള തയ്യാറെടുപ്പുകൾ ആരംഭിക്കാൻ  സമയമായി. പരീക്ഷയിൽ വിജയിക്കുന്നതിന്, സിലബസിനെക്കുറിച്ച് വ്യക്തമായ ധാരണ ഉണ്ടായിരിക്കണം, അതിനാൽ കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് വിശദമായി വായിച്ച് മനസിലാക്കുക. ചുവടെ നൽകിയിരിക്കുന്നു ലിങ്ക് ഉപയോഗിച്ച് നിങ്ങൾക്ക് കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് PDF രൂപത്തിൽ ഡൗൺലോഡ് ചെയ്യാവുന്നതാണ്.

UEIL അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് 2023: അവലോകനം

ചുവടെ നൽകിയിരിക്കുന്ന പട്ടികയിൽ UEIL അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് 2023 സംബന്ധമായ എല്ലാ പ്രധാനപ്പെട്ട വിവരങ്ങളും ലഭിക്കും.

Fill out the Form and Get all The Latest Job Alerts – Click here

കേരള UNILEC അസിസ്റ്റന്റ് എഞ്ചിനീയർ പരീക്ഷാ പാറ്റേൺ 2023

അസിസ്റ്റന്റ് എഞ്ചിനീയർ UNILEC തസ്തികയുടെ പരീക്ഷാ പാറ്റേൺ ചുവടെ ചേർക്കുന്നു.

കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ പരീക്ഷാ തീയതി 2023

കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് PDF

കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് PDF ഡൗൺലോഡ് ചെയ്യാൻ, ചുവടെ നൽകിയിരിക്കുന്ന ലിങ്കിൽ ക്ലിക്ക് ചെയ്യുക.

കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് PDF

കേരള PSC അസിസ്റ്റന്റ് എഞ്ചിനീയർ സിലബസ് 2023

അസിസ്റ്റന്റ് എഞ്ചിനീയർ തസ്തികയുടെ വിശദമായ സിലബസ് ചുവടെ ചേർക്കുന്നു.

Civil Engineering

Module 1 (12 Marks)

• Buildings: Types of buildings, site selection, components of a residential building and their functions. Load bearing and framed structures; Brick and rubble masonry; Roofs and floors; Basic infrastructure services; Green buildings
• Building rules and regulations: Relevance of NBC, KBR & CRZ norms; Building area: Plinth area, built-up area, floor area, carpet area and floor area ratio for a building as per KBR.
• Surveying: objectives and principles. Linear, and angular and methods, Survey stations and Survey lines- ranging, Bearing of survey lines;
• Leveling: Principles and methods of leveling; Principle of Electromagnetic distance measurement (EDM), Principle of Total station
• Construction material: Conventional construction materials: types, properties and uses of building materials: bricks, stones, cement, sand and timber, Modern construction materials; Cement concrete: Constituent materials, types of cement and concrete, short-term and long-term properties of concrete; Steel: Structural Steel – Composition, material properties and behavior; Steel sections and steel reinforcements, types and uses.
• Construction Management: Types of construction projects; Tendering and construction contracts; Project planning and network analysis – PERT and CPM; Cost estimation
• Transportation Infrastructure: Geometric design of highways – cross-sectional elements, sight distances, horizontal and vertical alignment, Highway materials – desirable properties
• Environmental Engineering: Unit processes and operations for Water and Waste Water Treatment – primary and secondary treatments

Module 2 (13 Marks)

• Statics: basic principles of statics, composition and resolution of forces resultant and equilibrium equations; Friction; analysis of connected bodies; couple; General coplanar force system & forces in space – resultant and equilibrium equations. Centroid of composite areas, moment of inertia, Polar moment of inertia, mass moment of inertia
• Dynamics: rectilinear translation, equations of kinematics, kinetics, Motion on horizontal and inclined surfaces, motion of connected bodies. Impulse momentum equation and work energy equation; Curvilinear translation – equations of kinematics –projectile motion, kinetics, Moment of momentum and work energy equation.; Rotation – kinematics of rotation; Plane motion of rigid body; Simple harmonic motion –undamped free vibration of spring mass system of damping
• Solid Mechanics: Different types of supports, loads; Beams-Reactions at supports; Bending moment and shear force in statically determinate beams; Simple stress and strain relationships; Simple bending theory, Flexural and shear stresses, Uniform torsion; combined and direct bending stresses
• Soil Mechanics: Three-phase system and phase relationships, Index properties; Permeability – one-dimensional flow, Compaction of soils; One- dimensional consolidation, Pile load test, Bearing capacity of soil, functions of foundations, types – shallow and deep.
• Fluid Mechanics and Hydraulics: Properties of fluids, Fluid statics, Laminar and turbulent flow, Forces on immersed bodies, Flow in pipes; Flow measurement in channels and pipes, Water logging and drainage; Hydrologic cycle

Electrical Engineering

Module 1: [5 Marks]

Electrical Machines:

• DC Machines – Basics of Separately excited DC motor, Shunt and Series motors – Torque and power, back EMF, mechanical and electrical characteristics, Shunt DC generator and characteristics – EMF equation – external and internal characteristics.
• Three-phase induction motor: Principles and characteristics – Types – performance – standard tests – equivalent circuits – Starting and speed control. Operating principle of single-phase induction motors;
• Synchronous machines: cylindrical and salient pole machines, performance and characteristics, regulation and parallel operation of generators, starting of synchronous motors; Types of losses and efficiency calculations of electric machines.
• Single-phase transformers – Principles and construction – equivalent circuit – phasor diagrams – open circuit and short circuit tests – voltage regulation – efficiency, all-day efficiency – Autotransformer Three-phase transformers: connections, vector groups, parallel operation;

Module 2: [5 Marks]

• Power Systems – Generation, ac and dc transmission concepts, Models and performance of transmission lines and cables, Economic Load Dispatch, Series and shunt compensation, Electric field distribution and insulators, Distribution systems, Per unit quantities, ‐ Voltage and Frequency control, Power factor correction, Symmetrical components, Symmetrical and unsymmetrical fault analysis, Principles of over current, differential, directional and distance protection; Circuit ‐ breakers, System stability concepts, Equal area criterion.

Module 3: [5 Marks]

• Control Systems: Mathematical modelling and representation of systems, Feedback principle, transfer function, Block diagrams and Signal flow graphs, Transient and Steady state analysis of linear time ‐ invariant systems, Stability analysis using Routh-Hurwitz and Nyquist criteria, Bode plots, Root loci, Lag, Lead and Lead Lag compensators; ‐ P, PI and PID controllers.
• Electrical and Electronic Measurements: Bridges and Potentiometers, Measurement of voltage, current, power, energy and power factor; Instrument transformers, Digital voltmeters and multimeters, Phase, Time and Frequency measurement; Oscilloscopes, Error analysis. Digital energy meter.

Module 4: [5 Marks]

• Electrical System Design: Wiring systems, Earthing and protection equipment – MCB, RCCB
• Load Survey- common power ratings of domestic gadgets- connected load diversity factor-selection of number of sub circuits (lighting and power)- selection of MCB distribution boards to provide over load, short circuit and earth leakage protection. – Electrical System design for domestic and industrial installations – Pre-commissioning tests – Insulation resistance measurement, continuity test, polarity test and earth resistance measurement as applicable to domestic installations.
  Industrial installations – classifications- Design of electrical distribution systems with main switchboard, sub switchboards and distribution boards with ACBs, MCCBs and MCBs as the case may be, for feeding
  power (mainly motors) and lighting loads of small and medium industries. Selection of armored power cables (AYFY, A2XFY, YWY) – calculation of ampacity, voltage drop, short circuit withstand capacity etc.
• Design of MSB & SSB including Motor Control Centre (MCC) for motor controls – selection of bus bars and switchgears. Selection of 11kV indoor and outdoor transformer substations – selection of switchgears and protective devices – Short circuit calculations and earthing design for the HV and LV sides of an 11 kV substation.

Module 5: [5 Marks]

• Power Electronics: – Power semiconductor devices – Thyristor, MOSFET, IGBT – Static V-I characteristics and firing/gating circuits; DC to DC conversion: Buck, Boost and Buck-Boost Converters; Single and three-phase configuration of fully-controlled and semi-controlled rectifiers; Line harmonics of controlled rectifiers – Power factor and Distortion Factor of ac to dc converters; Single-phase and three-phase voltage and current source inverters, 120 degree and 180 degree conduction modes – sinusoidal pulse width modulation.

Mechanical Engineering

Module 1 : Theory of Machines and Machine Design; (5 marks)

• Concept of simple machine, Four bar linkage and link motion, Flywheels and fluctuation of energy, Power transmission by belts – Vbelts and Flat belts, Clutches – Plate and Conical clutch, Gears – Type of gears, gear profile and gear ratio calculation, Governors – Principles and classification, Riveted joint, Cams, Bearings, Friction in collars and pivots.

Module 2 : Engineering Mechanics and Strength of Materials; (5 marks)

• Equilibrium of Forces, Law of motion, Friction, Concepts of stress and strain, Elastic limit and elastic constants, Bending moments and shear force diagram, Stress in composite bars, Torsion of circular shafts, Bucking of columns – Euler’s and Rankin’s theories, Thin walled pressure vessels. Thermal Engineering.

Module 3 : Thermal Engineering Properties of Pure Substances; (5 marks)

• P-V & P-T diagrams of pure substance like H2O, Introduction of steam table with respect to steam generation process; definition of saturation, wet & superheated status. Definition of dryness fraction of steam, degree of superheat of steam. H-s chart of steam (Mollier’s. Chart).
• 1st Law of Thermodynamics: Definition of stored energy & internal energy, 1st Law of Thermodynamics of cyclic process, Non Flow Energy Equation, Flow Energy & Definition of Enthalpy, Conditions for Steady State Steady Flow; Steady State Steady Flow Energy Equation.
• 2nd Law of Thermodynamics: Definition of Sink, Source Reservoir of Heat, Heat Engine, Heat Pump & Refrigerator; Thermal Efficiency of Heat Engines & co-efficient of performance of Refrigerators, Kelvin –Planck & Clausius Statements of 2nd Law of Thermodynamics, Absolute or Thermodynamic Scale of temperature, Clausius Integral, Entropy, Entropy change calculation of ideal gas processes. Carnot
  Cycle & Carnot Efficiency, PMM-2; definition & its impossibility.
• Air standard Cycles for IC engines: Otto cycle; plot on P-V, T-S Planes; Thermal Efficiency, Diesel Cycle; Plot on P-V, T-S planes; Thermal efficiency. IC Engine Performance, IC Engine Combustion, IC Engine Cooling and lubrication.
• Rankine cycle of steam: Simple Rankine cycle plot on P-V, T-S, h-s planes, Rankine cycle efficiency with & without pump work.
• Boilers: Classification; Specification; Fittings & Accessories: Fire Tube & Water Tube Boilers. Air Compressors & their cycles: Refrigeration cycles; Principle of a Refrigeration Plant; Nozzles & Steam Turbines

Module 4 : Fluid Mechanics & Machinery Properties & Classification of Fluid; (5 marks)

• Ideal & real fluids: Newton’s law of viscosity, Newtonian and NonNewtonian fluids, compressible and incompressible fluids.
• Fluid Statics: Pressure at a point. Measurement of Fluid Pressure: Manometers, U-tube, Inclined tube.
• Fluid Kinematics: Stream line, laminar & turbulent flow, external & internal flow, continuity equation.
• Dynamics of ideal fluids: Bernoulli’s equation, Total head; Velocity head; Pressure head; Application of Bernoulli’s equitation.
• Measurement of Flow rate Basic Principles: Venturimeter, Pilot tube, Orifice meter. Hydraulic Turbines: Classifications, Principles.
• Centrifugal Pumps: Classifications, Principles, Performance.

Module 5: Production Engineering; (5 marks)

• Classification of Steels: mild steel & alloy steel, Heat treatment of steel,
• Welding: Arc Welding, Gas Welding, Resistance Welding, Special Welding Techniques i.e. TIG, MIG, etc. (Brazing & Soldering), Welding Defects & Testing; NDT,
• Foundry & Casting: methods, defects, different casting processes, Forging, Extrusion, etc,
• Metal cutting principles: cutting tools, Basic Principles of machining with (i) Lathe (ii) Milling (iii) Drilling (iv) Shaping (v) Grinding, Machines, tools & manufacturing processes.

Electronics & Communication Engineering

Module-1 – 6 marks

• Solid state devices
  Fermi-Dirac Distribution function, carrier concentration at equilibrium, parameters associated with generation, recombination and transport mechanism, Drift and diffusion currents and current density in extrinsic semiconductors, Current components and current equation in a pn junction diode and bipolar junction transistor, Basic MOS physics, scaling of MOSFETs, short channel effects
• Network theory
  Mesh / Node analysis, Network Theorems, the steady-state response of the linear time-invariant networks,
  Transient response of RLC networks, Network functions, Network Parameters, Analysis of single-port and two-port networks
• Analog circuits
  Analog circuits using diodes, first-order RC circuit, Amplifiers using BJT and MOSFET, Oscillators and regulated power supply circuits

Module-2 – 4 marks

• Logic circuit design
  Digital logic and Boolean algebra, combinational logic using AND/OR/NOT gates/Multiplexers, Logic families, Implementation of sequential logic circuits, and Verilog models.
• VLSI design
  Methodologies in ASIC and FPGA design, VLSI Logic circuits with MOSFET logic families, memory elements, Design of arithmetic circuits, MOSFET fabrication techniques

Module-3 – 5 marks

• Electromagnetics
  Basic mathematical concepts related to electromagnetic vector fields, Maxwell’s equation, electromagnetic wave propagation and wave polarization, characteristics of transmission lines, solving with Smith chart, propagation of EM waves in Wave guides
• Microwave and antennas
  The basic concept of antennas and their parameters, far field pattern of Short dipole and Half wave dipole antennae, the Design of broadband antennas, arrays and its radiation patterns, cavity resonators and microwave sources, microwave hybrid circuits and microwave semiconductor devices

Module-4 – 5 marks

• Signals and systems
  Properties of signals and systems, Representation of signals with the help of series and transforms, orthogonality of signals and convolution integral, LTI response to input signals, discretize continuous-time signals
• Digital Signal Processing
  Properties and relations of DFT, DFT-based filtering methods, DFT and IDFT using DIT and DIF radix-2 FFT algorithms, linear phase FIR filters and IIR filters, FIR and IIR filter structures, multi-rate DSP operations decimation and interpolation, the architecture of DSP processor

Module-5 – 5 marks

• Analog and Digital communication
  analog communication systems, concepts of random processes to LTI systems, waveform coding techniques in digital transmission, GramSchmitt procedure to develop digital receivers, equalizer design to counteract inter-symbol interference (ISI), digital modulation techniques in signal transmission
• Information theory and coding
  Measures of information – entropy, conditional entropy, mutual information, Shannon’s source coding theorem for data compression, concept of channel capacity, linear block codes for error detection and correction, algebraic codes for error correction, encoding and decoding of convolutional and LDPC codes

Sharing is caring!