Engineering Jobs   »   Quiz: Electrical Engineering 2 May 2020

Quiz: Electrical Engineering 2 May 2020

Quiz: Electrical Engineering
Exam: NLC
Topic: Miscellaneous
Each question carries 1 mark.
Negative marking: 1/4 mark
Time: 10 Minute

Q1. In a vacuum cleaner, we generally use ………. motor.
(a) shunt
(b) cumulatively compounded
(c) series
(d) differentially compounded


Q2. A 220 V series motor takes a current of 35 A and runs at 955 r.p.m. Armature resistance = 0.25 Ω and series field resistance = 0.3Ω If iron and friction losses amount to 600 W, what is the armature torque?
(a) 140.52 Nm
(b) 118.5 Nm
(c) 70.26 Nm
(d) 35.13 Nm



Q3. The armature torque of a d.c. motor running at 850 r.p.m. is 97.3 Nm and shaft torque is 91.3 Nm. The iron and friction losses are
(a) 502.90 W
(b) 400 .00W
(c) 534.03 W
(d) 332.46 W



Q4. A d.c. motor runs at 1825 r.p.m. at full-load and 1875 r.p.m. at no-load. The speed regulation is ………
(a) 3.7%
(b) 2.7%
(c) 4.6%
(d) 9.5%



Q5. A transformer transfers electrical energy form primary to secondary usually with a change in ……….
(a) Voltage
(b) Power
(c) Frequency
(d) Energy



Q6. A 230/2300 V transformer takes no-load current of 7.5 A and absorbs 195 W. If the resistance of the primary is 0.07 Ω, what is the core loss?
(a) 128.5 W
(b) 191.07 W
(c) 288.4 W
(d) 199.3 W



Q7. A generating station has a connected load of 49 MW and a maximum demand of 21 MW; the units generated being 61.5 × 106 kWh per annum. The demand factor is
(a) 0.428
(b) 0.683
(c) 0.500
(d) 0.496



Q8. For quick operation from zero to full load condition which of the following power plant is most suited…?
(a) nuclear power plant
(b) hydro-electric plant
(c) steam power plant
(d) gas turbine plant



Q9. The cost of an overhead line will increase if
(a) conductor spacing is decreased
(b) Conductor spacing is increased
(c) ground clearance is decreased
(d) Cheaper conductor is used



Q10. Corona is affected by
(a) condition of atmosphere
(b) size and spacing of conductors
(c) line voltage
(d) all of the above




S1. Ans.(c)
Sol. we generally use series motor.


S2. Ans.(c)
Sol. Motor resistance, Rm=0.25+0.3=0.55 Ω;Eb=V 〖-I〗a Rm=220-35×0.55= 200.75 V
Armature torque, Ta=9.55×(Eb Ia)/N=9.55×(200.75×35)/955=70.2625 Nm



S3. Ans.(c)
Sol. Lost torque = Ta-Tsh = 97.3 – 91.3 = 6 Nm
Also, Lost torque = 9.55 × (Iron and friction loss)/N
∴ Iron and friction loss = (6 × 850)/9.55= 534.03 W



S4. Ans.(b)
Sol. Speed regulation = (N0 -NFL)/NFL ×100=(1875-1825)/1825×100 = 2.74%



S5. Ans.(a)
Sol. Voltage



S6. Ans.(b)
Sol. No. load loss, W0=195 W ; Primary Cu loss = I0^2 R1=(7.5)^2×0.07=3.93 W
Iron loss = W0-Primary Cu loss = 195 – 3.93 = 191.07 W



S7. Ans.(a)
Demand Factor=(Max.demand)/(connected load)=21/49=0.428


S8. Ans.(b)
Sol. Hydro-electric plant does not require a long starting time. In fact, such a plant can be put into service instantly.



S9. Ans.(b)
Sol. Conductor spacing is increased



S10. Ans.(d)
Sol. Corona is affected by condition of atmosphere, size and spacing of conductors & line voltage.

Sharing is caring!

Thank You, Your details have been submitted we will get back to you.

Leave a comment

Your email address will not be published.